cuisinart dcc-1200 coffee maker manual

The Cuisinart DCC-1200 is a 12-Cup Programmable Coffeemaker featuring a 24-hour programmability, auto shut-off, pause & serve function, and a charcoal water filter. It includes a glass carafe with ergonomic handle, a permanent gold-tone filter, and a cleaning indicator light. Below are key sections for safety, features, setup, operation, cleaning, and troubleshooting.

Features at a Glance

Key components: 12-Cup Glass Carafe, Charcoal Water Filter, Permanent Gold-Tone Filter, Control Panel with LCD Display.

Installation & Setup

Unpack and inspect all parts. Place on a clean, dry, level surface away from edges.

1. Insert Charcoal Filter: Soak filter in water for 15 minutes, then place in filter holder.
2. Install Permanent Filter: Place gold-tone filter into the filter basket.
3. Attach Carafe: Ensure carafe is properly seated on the warming plate.
4. Plug into 120V AC outlet.

WARNING! Keep cord away from hot surfaces. Do not immerse base, cord, or plug in water.

First-Time Use

Before first brew, clean the coffeemaker by running a cycle with water only.

1. Fill water reservoir to 12-cup mark with clean water.
2. Place empty carafe on warming plate.
3. Press the ON/OFF button to start cleaning cycle.
4. Discard water after cycle completes. Repeat if desired.
5. Your coffeemaker is now ready for brewing.

CAUTION! Use only cold water. Do not use without water in the reservoir.

Specifications

• Capacity: 12 cups (5.7 oz per cup).
• Power: 120V AC, 60Hz, 900W.
• Dimensions: Approximately 11.5" H x 8.5" W x 10.5" D.
• Carafe: Glass, 12-cup capacity with ergonomic handle.
• Filter: Permanent gold-tone filter; includes charcoal water filter.
• Programmability: 24-hour advance brew start.
• Auto Shut-Off: Programmable from 0 to 4 hours.
• Brew Strength: Regular or Bold setting.
• Warranty: Limited 3-year warranty.

Controls and Settings

Control Panel: ON/OFF, PROGRAM, HOUR, MINUTE, AUTO ON, AUTO OFF, BREW STRENGTH, CLEAN.

LCD Display: Shows time, programming status, and clean indicator.

Settings: Set clock using HOUR and MINUTE buttons. Program brew time using PROGRAM, HOUR, MINUTE. Select brew strength (Regular/Bold) before brewing. Set auto shut-off duration (0-4 hrs) with AUTO OFF. Clean indicator light illuminates when descaling is needed.

Programming & Operation

To brew coffee immediately or on a programmed schedule.

1. Fill water reservoir to desired cup level.
2. Add coffee grounds to filter (1 tbsp per cup).
3. Place carafe on warming plate.
4. For immediate brew: Press ON/OFF.
5. To program: Press PROGRAM, then set time with HOUR/MINUTE. Press AUTO ON to activate.
6. Use Pause & Serve during brewing by carefully removing carafe.
7. Auto Shut-Off: Press AUTO OFF to set duration (0-4 hrs).

Tip: For best results, use fresh, cold water and grind coffee just before brewing.

Cleaning & Maintenance

Regular cleaning ensures optimal performance and coffee flavor.

1. Daily: Wash carafe, lid, and filter basket in warm, soapy water. Rinse thoroughly.
2. Monthly: Descale using vinegar solution or commercial descaling agent.
3. Charcoal Filter: Replace every 60 uses or 2 months (whichever comes first).
4. Exterior: Wipe with damp cloth. Never use abrasive cleaners.

WARNING! Unplug and allow to cool completely before cleaning. Do not immerse base in water.

Care Instructions

Descaling: When CLEAN light illuminates, run a cycle with equal parts white vinegar and water, then run 2 cycles with clean water.

CAUTION! Mineral buildup can affect performance. Descale regularly based on water hardness.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Cuisinart. For support, visit www.cuisinart.com or contact 1-800-726-0190.

Troubleshooting

Reset: Unplug for 10 minutes to reset electronic controls.

Service: 1-800-726-0190; www.cuisinart.com