cuisinart dcc 3000 instruction manual

The Cuisinart DCC-3000 is a programmable 12-cup coffeemaker featuring a 24-hour advance brew start timer, auto shut-off, self-cleaning function, and a charcoal water filter. It includes a stainless steel carafe, permanent coffee filter, and a measuring scoop. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Programmable control panel, stainless steel carafe, permanent filter, charcoal water filter, measuring scoop.

Installation

Unpack and inspect contents. Place on clean, dry, level surface.

1. Insert charcoal filter: Soak filter in water for 15 minutes, then place in filter holder.
2. Install permanent filter: Place in filter basket.
3. Add water: Fill reservoir with cold water (up to 12 cups).
4. Plug into AC power outlet.

WARNING! Do not immerse coffeemaker in water. Keep cord away from heated surfaces.

First-Time Setup

Before first use, run a cleaning cycle.

1. Set time: Press and hold CLOCK, use HOUR/MIN to set current time.
2. Clean: Fill reservoir with water, press CLEAN to run self-cleaning cycle.
3. Brew a test pot: Use water only to remove any residual taste.
4. Program timer: Set desired brew time using PROGRAM button.

CAUTION! Ensure carafe is properly seated on warming plate before brewing.

Specifications

• Capacity: 12 cups (60 oz).
• Power: 120V AC, 60Hz, 900W.
• Carafe: Stainless steel, thermal.
• Filter: Permanent gold-tone filter included.
• Water Filter: Charcoal filter (replace every 60 cycles or 2 months).
• Timer: 24-hour programmable.
• Auto Shut-Off: 0 to 4 hours adjustable.
• Dimensions: Standard countertop size.
• Warranty: 3-year limited warranty.

Controls and Settings

Control Panel: POWER, PROGRAM, CLOCK, HOUR, MIN, CLEAN, STRENGTH, AUTO OFF.

Functions: Set clock, program brew time, adjust brew strength, set auto shut-off duration, activate cleaning cycle.

Brew Strength: REGULAR (standard) or BOLD (stronger flavor). Auto Shut-Off: Set to 0, 2, or 4 hours after brewing. Cleaning: Press CLEAN to start self-cleaning cycle (run with water only).

Brewing Coffee

For manual brewing or using programmed timer.

1. Add water: Fill reservoir to desired cup level.
2. Add coffee: Place ground coffee in filter (1 tbsp per cup).
3. Brew: Press POWER to start immediate brewing.
4. Pause: Use BREW PAUSE to pour a cup during brewing.
5. Serve: Carafe keeps coffee warm on heating plate.

Tip: Use fresh, cold water and medium grind coffee for best results.

Programming & Timer

Set coffeemaker to brew automatically at a specific time.

1. Set current time: Hold CLOCK, adjust with HOUR/MIN.
2. Set brew time: Press PROGRAM, use HOUR/MIN to set desired brew time.
3. Confirm: Display shows programmed time.
4. Add coffee and water the night before.
5. Coffeemaker will brew at set time.

Note: Power must remain on for timer to function.

Care & Cleaning

Unplug before cleaning. Clean carafe, filter basket, and exterior regularly.

1. Daily: Empty and rinse carafe and filter basket.
2. Weekly: Run self-cleaning cycle (water only).
3. Monthly: Descale with vinegar solution (1 part vinegar to 2 parts water).
4. Filter: Replace charcoal filter every 60 cycles.

CAUTION! Do not use abrasive cleaners. Never immerse base in water.

Regulatory Information

UL listed. FCC Part 15 compliant. Copyright © Cuisinart. For support, visit www.cuisinart.com or contact 1-800-726-0190.

Troubleshooting

Reset: Unplug for 10 seconds, then plug back in.

Service: 1-800-726-0190; www.cuisinart.com